XS+DA0001
SFP 1G and SFP+ 10G, but also the 25G SFP28 standard
This is highly cost-effective way to connect two SFP/SFP+/SFP28 devices (for example two units of our new CCR2004-1G-12S+2XS) for very short distances, within racks and across adjacent racks.
950.00 ฿
CompareRelated products
-
Ethernet routers, Mikrotik
CCR2004-16G-2S+
0 out of 5(0)Like the other models in CCR2004 series, this CCR also features the Annapurna Labs Alpine v2 CPU with 4x 64-bit ARMv8-A Cortex-A57 cores running at 1,7GHz. But here’s the difference. This powerful router crushes all previous CCR models in single-core performance, and that is the most important aspect when it comes to heavy operations based on per-connection processing. Like queues, for example.But that’s not all! It also has the best single-core performance per watt and best overall performance per watt among all the CCR devices. Better for the planet, better for the bills, it’s a win-win!
SKU: n/a15,000.00 ฿17,000.00 ฿ -
Mikrotik, Accessories, Interfaces
S+RJ10
0 out of 5(0)S+RJ10 module is supported also on devices with passive cooling, but may require an extra cooling.
The latest revision of S+RJ10 contains “/r2” by the end of serial number. It comes with following improvements:
– Jumbo frames up to 10218 Bytes are now supported for rates 2.5Gbps, 5Gbps and 10Gbps;
– Link speed reporting is fixed – actual link speed in the interface menu is listed. Previously 100M/1G/2.5G/5G link speeds were not reported correctly;
– DDM monitoring (Supply Voltage, Module temperature) is now supported.
SKU: n/a2,100.00 ฿ -
Mikrotik, Ethernet routers
RB5009UG+S+IN
0 out of 5(0)The board features 9 wired ports and a full-sized USB 3.0. Seven of the ports are Gigabit Ethernet, another one is 2.5 Gigabit Ethernet, and the last one is a 10G SFP+ cage. All the ports are connected to a powerful Marvell Amethyst family switch-chip with a 10 Gbps full-duplex line leading to the Marvell Armada Quad-core ARMv8 1.4 GHz CPU. Both CPU and the switch-chip are located on the bottom of the board – so the case acts as a massive heat-sink!
RB5009UG+S+IN can be powered in 3 different ways:
a) PoE-in from Ethernet port #1
b) DC Jack
c) 2-pin terminal on the side
SKU: n/a7,200.00 ฿ -
Mikrotik, Power supplies
RBGPeR
0 out of 5(0)The GPeR unit allows to extend Ethernet cable by additional hop (< 100 – 150 m to regular network devices, and up to 210 m to another GPeR unit) up to 1,500 m.
Handy for highrise buildings, multi-apartment buildings, with many floors and sections, where very long Ethernet cables might be a problem.
Maximum allowed length of CAT6 Ethernet cable between GPeR and power source/router is up to 100 m (depending on cable quality, high quality – up to 150 m).
Maximum allowed distance of CAT6 Ethernet cable between two GPeR devices is up to 210 m (depending on cable quality).
In case if the destination device does not support PoE-in powering, the PoE Passthrough can be disabled by manually removing all jumpers.
SKU: n/a1,250.00 ฿